Dimming Mode	0-10V PWM Dimming/ Traic Dimming	Output Current	12.5A
Output Type	Single	Output Voltage	12V
Output Frequency	50/60Hz	Input Voltage	170-264Vac
Output Power	150W	Warranty	3 Years
Size	251.5*46.5*30mm	Material	Aluminium
IP Level	IP20 For Indoor	OEM	Yes
Protection	Over-load, Over-voltage, Over-current, Short-circuit	Type	Constant Voltage
High Light	Dimming 150W LED Driver, PWM 150W LED Driver, LED Power Supply 10V

Product Specification

0-10V PWM Dimming 150W LED Driver LED Power Supply for LED Colorful Strips and LED light

1) Applications

2) Product Features

Single output, output voltage

0-10V PWM Dimming

High efficiency up to 86%

Dimming effect smooth, no flicker

Protections: Short circuit, over load, Over voltage

3) Output Characteristics

1. Output Power

Voltage	Min. Load	Rated Load	Peak@10mS	Rated Output Power
DC 0-12V	0A	12.5A	180W	150W

2. Line Regulation

Voltage	Min. Load	Rated Load	Line Regulation	Load Regulation
DC 0-12V	0A	12.5A	±3%	±5%

3. Ripple and Noise

Under nominal voltage and nominal load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point.

Voltage	Ripple and Noise(Max.)
12V DC	200mV p-p

4. Turn on delay time: 2Second Max.at 220Vac input and output Max.load.

5. Rise time:400 mS Max.at 220Vac input and output Max load.

6. Efficiency: 86% Min, At220Vac input voltage and full load calculation efficiency.

7. Overshoot: 5% Max.When power supply at turn or turn off.

4) Protection Functions

1. Short circuit protection: auto recovered when short circuit faults remove.

2. Over Voltage Protection: Hiccup mode

3. Over load protection: auto recovered when over current faults remove.

5) Test

Drop test, Salt Spray Test, Surge test, Ageing test, lightning test, Temperature Variation test etc.

6)  Safety Requirement

1. Safety Standard: Safety: Design by IEC60950 standard.

2. DIELECTRIC STRENGTH Hi-Pot:
Primary to secondary:1200Vac/10mA/60S for type test.
Primary to case:1200Vac/10mA/60S for type test.
Secondary to case:300Vac/10mA/60S for type test.

3. Iusulation resistance:Primary to secondary:10MΩ min at 500V DC.

7) EMI Requirement

Designed according to the following standards:

1. FCC class B rules

2. EN55022 class B rules

3. GB9254-1998,GB17625.1-2003

8) OEM

Customize label and Inner box

9) Cautions

1This product should be installed by qualified personnel.

2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.

3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.

4.Please make sure LED power supply output voltage, current is used to meet the product requirements.

5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.

6.Due to safety concerns, PVC or rubber cord of 0.75- 1.5mm² is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.

7.In case of malfunction, do not repair it yourself.

 

Factory Capacibility

1. Professional manufacturer

17 Years experience,  10,000 square meters factory, 400+ employees,  8 production lines

2. Scientific Management

ISO9001:2015 Quality Management System Certified, 7S administration

3. Independent R&D teams

10+ Engineer teams, innovative and independent R&D ability

4. Advanced equipment

SMT plant,  wave-soldering machine,  Semi-auto assembling, EMC lab, Test Lab, Ageing room etc.